This article will explain how to calibrate the AUTOMATiQ, using the integrated BOSCH System.

When to conduct a calibration

Calibrating the automatic shifting interface is always needed after one of the following:

• After the initial assembly of the e-bike.
• When the automatic shifting hub interface (e.g. AUTOMATiQ) was removed for maintenance reasons.
• When the system does not work properly.

Calibration options

These are the many ways you can calibrate an AUTOMATiQ hub interface:

With a smartphone or tablet

• How to calibrate the new AUTOMATiQ using the enviolo App

With a CLiQ controller

• How to calibrate the AUTOMATiQ using the CLiQ controller

With the bike's integrated system

• How to calibrate the AUTOMATiQ using a BOSCH integrated display
• How to calibrate the AUTOMATiQ using the Bafang integrated display
• How to calibrate the AUTOMATiQ using the FIT integrated display
• How to calibrate the AUTOMATiQ using the Specialized integrated display

Step-by-step instructions

BOSCH Intuvia

Video

Tools

• A bicycle with a BOSCH Intuvia integrated system.
  

Calibration instructions

1. Turn on the Bosch Intuvia system.
2. Select no motor assist.
3. Activate the "configuration mode" through simultaneous push and hold of [RESET] and [i] buttons (A & B).
   
4. Push the [i] button (B), until you can see "gear calibration" on the screen.
5. While pedaling, press the "Light" button (C) to start calibration.
6. Pedal the e-bike lightly through the entire calibration process (preferably on a stand with the rear wheel off the ground), while the system shifts from full underdrive to full overdrive multiple times and completes the calibration process.
   • This process can take ~25 seconds.
7. After completion of the calibration process, the system returns to the ride mode automatically.

BOSCH Nyon 2

Video

Tools

• A bicycle with a BOSCH Nyon 2 integrated system.
  
  

Calibration instructions

1. Turn on the Bosch Nyon system.
2. Select no motor assist.
3. Enter the "Settings" menu by pressing the [>] and [<] keys and confirm your selection with the pound key [<>].
4. Use [+] and [-] to select the menu item "My eBike" and confirm your selection with [<>] or [>].
5. Select the menu item "eShift" and confirm your selection.
6. Select the menu item "Calibration" and confirm your selection.
7. Pedal the e-bike lightly through the entire calibration process (preferably on a stand with the rear wheel off the ground), while the system shifts from full underdrive to full overdrive multiple times and completes the calibration process.
   •  This process can take ~25 seconds.
8. After completion of the calibration process exit the menu.

BOSCH Kiox

Video

Tools

• A bicycle with a BOSCH Kiox integrated system.
  

Calibration instructions

1. Turn on the Bosch Kiox system.
2. Select no motor assist.
3. Enter the "Settings" menu by pressing the [>] and [<] keys and confirm your selection with the pound key [<>].
4. Use [+] and [-] to select the menu item "My eBike" and confirm your selection with [<>] or [>].
5. Select the menu item "eShift" and confirm your selection.
6. Select the menu item "Calibration" and confirm your selection.
7. Pedal the e-bike lightly through the entire calibration process (preferably on a stand with the rear wheel off the ground), while the system shifts from full underdrive to full overdrive multiple times and completes the calibration process.
   •  This process can take ~25 seconds.
8. After completion of the calibration process, the system returns to the ride mode automatically.

Calibration done

If you followed all the steps the e-bike is ready to go. If you have any questions, please contact our Support team.